CD-55A INSTALLATION GUIDE FOR WINDOWS 95 Rev. C This driver is for TEAC CD-55A 8 BIT I/F card, TEAC CD-55A 16 BIT I/F card (P/N E950228-00A) and Sound Blaster card with Panasonic interface. ********************************** NOTE ************************************** * This driver does not work with Sound Blaster Compatible card. * ****************************************************************************** 1. If you would like to upgrade to Windows 95 from Windows 3.1 or Windows 3.11 (DOS 5.0 or higher) by using CD-55A: 1-1 Install the device driver in your config.sys and CD-ROM Extension program in your autoexec.bat by using CD-55A CD-ROM Installation Disk (P/N T000022-00C). Please refer to Software manual to install the device driver. 1-2 Reboot your system after the installation complete and let the system recognize CD-55A. 1-3 When your system recognize CD-55A, you can install Windows 95 from CD-55A. ----> GOTO How to install the protect mode driver Note: You may set the I/O address manually. Refer to How to set the I/O address 2. If you have already installed Windows 95 and you would like to install CD-55A: ----> GOTO How to install the protect mode driver 3. If you have already installed both Windows 95 and CD-55A: ----> GOTO How to install the protect mode driver Note: You may set the I/O address manually. Refer to How to set the I/O address How to install the protect mode driver Please call our BBS to get the protect mode driver. You will get compressed file CD55_W95.ZIP which consists of 4 files as follows: TEAC4X08.INF TEAC4X16.INF TEAC4X .MPD README .TXT You must decompress CD55_W95.ZIP file by using PKUNZIP.EXE program. Boot up Windows 95 and go to "Control Panel", double-click "Add New Hardware". Click "Next" to begin installing CD-55A and select "No" because you can't search CD-55A automatically. Then click "Next". Select "CD-ROM controller" as Hardware type and click "Next". Click "Have Disk". If the disk isn't in Drive A, change the drive letter or directly. Then click "OK". Find "TEAC4x CD-ROM Drive w/8 bit card" and "TEAC4x CD-ROM Drive w/16 bit card" in Models and select as follows: TEAC 8 bit I/F card : "TEAC4x CD-ROM Drive w/8 bit card" TEAC 16 bit I/F card : "TEAC4x CD-ROM Drive w/16 bit card" Sound Blaster : "TEAC4x CD-ROM Drive w/8 bit card" Click "Next". Confirm the I/O address setting. If this address is different from your hardware I/O address (dip, jumper switches), you must set same address later. However, if you have Sound Blaster, the address should be hardware I/O address + 0010H as follows: Sound Blaster hardware I/O address 220H -----> 230H Sound Blaster hardware I/O address 240H -----> 250H Click "Next", then the driver will be installed. Click "Finish" to complete the installation. If you had the same address as your hardware, Click "OK" to shut down your computer and let it recognize CD-55A. If you had the different address as your hardware, Click "NO" to setup properly and go to "How to set the I/O address". How to set the I/O address Double-click "System" in "Control Panel". Select "Device Manager" and double-click "CD-ROM controllers". "TEAC4x CD-ROM Drive w/8 bit card" or "TEAC4x CD-ROM Drive w/16 bit card" appears and double-click it. Select "Resources" and click "Change Setting". You must select the correct address from the following address. Value for 8 bit: 0230 - 0237 Value for 16 bit: 02C0 - 02C7 0250 - 0257 02E0 - 02E7 0270 - 0277 0300 - 0307 0290 - 0297 0320 - 0327 0300 - 0307 0340 - 0347 0310 - 0317 0360 - 0367 Click "OK" twice and click "OK" to restart again. How to run DOS application in MS-DOS mode If you install the protect mode driver, your CD-ROM extension program in your AUTOEXEC.BAT file (MSCDEX.EXE or CORELCDX.COM) is remarked automatically. It is to avoid their conflict. Therefore, if you want to use CD-55A in MS-DOS mode, you have to add the following statement in DOSSTART.BAT by using DOS Editor C:\WINDOWS\COMMAND\MSCDEX.EXE /D:TEAC-CDA /M:15 * C:\WINDOWS [Windows 95 directly] TEAC-CDA [Drive Name same as TEAC_CDA.SYS in your CONFIG.SYS] If you don't have DOSSTART.BAT in Windows 95 directly (C:\WINDOWS), you have to make DOSSTART.BAT file. DOSSTART.BAT must run when you exit to DOS from Windows shut down menu. If you don't recognize CD-55A, please check whether your CONFIG.SYS file has the device driver TEAC_CDA.SYS statement still. If your CONFIG.SYS file doesn't have the device driver TEAC_CDA.SYS statement, you have to add the statement manually by using DOS Editor. TEAC_CDA.SYS must be load from CONFIG.SYS file. Caution! If you install the real mode driver by using CD-55A CD-ROM Installation Disk (P/N T000022-00C) after installing the protect mode driver, your system will hang up unless you exit from the procedure that the install program edit your AUTOEXEC.BAT and CONFIG.SYS files. ============================================================================== Technical support ============================================================================== TEAC America Inc. Phone 213-727-4860 BBS 213-727-7660 Fax on Demand 213-727-7629 ==============================================================================